You are now leaving Polygon Restoration's website and will be directed to another country in the group.
Do you want to proceed?
Our customer had been contracted to prep the surfaces and to apply a coating liner system on the interior sections of two newly constructed giant crude oil storage tankers. Each tank was 225 feet in diameter and 62 feet high with a floating roof. The assignment was to abrasive blast the inside surfaces of the steel tanks, clean out the abrasive, prepare a clean, dry surface for coating and spray the coatings on the floors and walls to a height of two feet above the floors with an epoxy coating. The two-foot height for coating the walls was specified to protect the surface against water that accumulates in the tank and can rise to that level below oil stored in the tanks.
Because the customer needed to meet a deadline to store incoming crude oil, the challenge was to complete both tanks within 28 days, versus a normal 60-day schedule. This demanding schedule had to be met during a cool, rainy period, which was likely to create condensation on the work surface of the tank.
“The major threat to the integrity of the coating was the possibility of the formation of ‘rust bloom’ corrosion that can occur on steel surfaces between the blasting phase and application of the paint, during damp conditions,”
“The atmosphere is normally very humid, but conditions in April were made worse by heavy rains. This meant we could expect condensation on the inside of the tank.”
Because of the humid air and cool outside temperatures, condensation could easily form on the inside tank surfaces during the work period.
“We knew we could never meet the job specifications under those conditions. We needed to first create a dry atmosphere and lower the dew point inside the tanks. We also needed to keep the temperature high enough to speed the cure rate of the coating.”
For a solution our client turned to Polygon, his provider of dehumidification services for the past 15 years. Polygon was asked to build a rental system that would hold the blast by eliminating any possibility of condensation forming on the tank walls. After analysing the project parameters, Polygon experts suggested the use of propane gas fired desiccant dehumidifier units, which are effective in removal of high levels of moisture at high rates of airflow. An added advantage of using the desiccant units in this situation was the ability to utilize the heat that is a natural by-product of the dehumidification process to boost the cure rate of the coating. With Polygon’s system in place, work could continue around the clock for 13 days on each tank. As a result, the desiccant dehumidifiers assured that the company met the deadline and saved money in the process.
This reduced costs in several ways:
Polygon allowed continuous work to proceed in a constant humidity-controlled environment. All surface preparation could be completed before cleaning and coating.
Lower Fuel Cost.
Polygon propane reactivated dehumidifiers require only limited electrical power to operate. As a result, small generators could be used at the remote site, which saved on diesel fuel. Excellent Curing Heat from the dehumidification process was used inside the tank, eliminating the need for a bake-out service to cure the coating. Because heat was in the tank throughout the coating application, cure time was reduced, as well.
Completion was On Time
According to the client, “Without the Polygon Temporary Humidity Control to control the climate in the tanks, we never would have been able to meet the job completion deadline. Being able to do that helped enhance our relationship with our client and helps build our reputation.”
The Polygon Advantage
Polygon has the engineering knowledge to build an integrated climate control system to meet all of the customer’s needs. From humidity and temperature control to dust collection or lead abatement, Polygon will build an efficient and dependable system sized appropriately for your job site.
• Substantial cost reductions
• Ensured coating performance
• Compliance with regulations
• Noise reduction
• 24-hour service and support
• Engineering knowledge
• Expert advice and experience
• Equipment to meet every need
Polygon hands lifeline to pupils by restoring school's hydrotherapy facility
Established over 175 years ago, Stranraer Academy today serves close to 1,000 pupils of all...
Polygon provides the correct environmental conditions to enable water tank repair
Direct Reaction Team
We are ready to respond on short notice to ensure that real estate and other property restored to its origins in the fastest possible way. We do a quick assessment of the damage to be able to take the right actions.
Your questions and comments are important to us. Select a topic and fill in the contact form. We´ve everything covered for your needs!
Blackstone Road, Huntingdon, Cambridgeshire, PE29 6EE
Phone: 01480 442327
By subscribing to our mailer list you are agreeing to receive information from Polygon UK.
We work in accordance to GDPR legislation. We will only use your personal data to communicate with you through our newsletters or to inform you about products, services or promotional offers that you might find interesting if you have chosen to receive these types of communications. We will never give your information to third parties. The data is stored in Mailchimp.
You can unsubscribe at any time from our mailer list via a link at the bottom of the newsletter or email that you receive from Polygon UK.